View DS2149DK_237990.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
www.maxim-ic.com
GENERAL DESCRIPTION
The DS2149DK/DS21349DK is a fully integrated design kit for the DS2149 and the DS21349 T1/J1 line interface units (LIUs). It contains the necessary circuitry to evaluate the device in all operation modes, including running the device in hardware and software mode.
FEATURES

PLCC 28-Pin Socket for Multiple Part Evaluation Bantam and RJ48 Connectors, Transformers, and Termination Passives for LIU Two Separate and Controllable Transmit Paths for TTIP and TRING for Evaluating Multiple Transformers Equipment-Side Connector for External Data Source/Sink or External Remote Loopback On-Board T1 Crystal Oscillator On-Board 8051 Microprocessor for Software Mode Access Connector Accesses to CS, SCLK, SDI, and SDO for Firmware Development Controllable 5V and 3.3V for VCC and IO Pins to Support the DS2149 and DS21349 LIUs
DESIGN KIT CONTENTS
DS2149DK/DS21349DK Board DS2149 28-Pin PLCC DS21349 28-Pin PLCC
ORDERING INFORMATION
PART DS2149DK/ DS21349DK DESCRIPTION T1/J1 Line Interface Unit Design Kit
1 of 14
REV: 032403
DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
COMPONENT LIST
DESIGNATION C1 C3, C6, C9, C12, C15-C17, C19 C4, C7, C10, C21 C5, C8, C11, C22, C23 C13, C14 C18, C20 DS1-DS3, DS5 DS7 J1 J2, J3 J4-J11 J12 JP1 JP2-JP6 JP7-JP10 PWR_CONNBAN2 PWR_CONNBAN1 R1-R3, R12, R14 R4, R5 R6, R7, R10, R11 R8, R9 R13, R15, R16 R17-R21 RN1, RN2 S1 SW1 SW2 T1 T2 T3 U1 U2, U5, U7 U3, U4, U6 U8 U9 U10 X1 Y1 QTY 1 8 4 5 2 2 4 1 1 2 8 1 1 5 4 1 1 5 2 4 2 3 5 2 1 1 1 1 1 1 1 3 3 1 1 1 1 1 DESCRIPTION 0.001mF capacitor (SMT80123) 10mF capacitors (SMT80123) 0.1mF capacitors (SMT80123) 0.01mF capacitors (SMT80123) 10mF capacitors (SMT127240) 22pF capacitors (SMT80123) Red LED 150-mil SO, DS87C520-ECL Connector, RJ48, 8-pin Bantam connectors COTO9802 100-mil, 16-pin vertical connector Pushbutton switch 100-mil SIP jumper 2 position 100-mil SIP jumper 3 position Banana connector, 2-pin, red Banana connector, 2-pin, black 300W resistors (SMT80123) 4.7W resistors (SMT80123) 0W resistors (SMT80123) 50.0W resistors (SMT80123) 10.0kW resistors SMT80123) 30W resistors (SMT80123) 1kW 10-pin resistor network 9-pin DB9P connector 10-position switch 6-pin DPDT switch 1:3 T1 transformer 1:2 T1 transformer 1:1 T1 transformer PLCCSMT28T0T socket 150-mil SO, 74HC04, hex inverter 150-mil SO, 74HC03, open collector NAND gate Darlington array 150-mil SO, DS232AR 3.3V regulator EC1-S-11.0592M XTAL low pro 1.544MHz crystal oscillator SUPPLIER Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Dallas Semiconductor Digi-Key Digi-Key Coto Technology Digi-Key Digi-Key Digi-Key Digi-Key Mouser Electronics Mouser Electronics Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Digi-Key Pulse Engineering Pulse Engineering Pulse Engineering Pioneer Electronics Digi-Key Digi-Key Texas Instruments Dallas Semiconductor Maxim Digi-Key Digi-Key -- -- -- -- -- -- LN1251C DS87C520-ECL 15-43-8588 RTT34B02 COTO9802 -- EVQPAE04M -- -- 164-6219 164-6218 -- -- -- -- -- -- -- 747459-1 435668-9 SSA22 PE-64933 PE-65771 PE-64936 PLCCSMT28T0T TC74HC04AFN SN74LS38D ULQ2003ADR DS232AR MAX8887EZK33 EC1-S-11.0592M NTH039A3-1.5440 PART
2 of 14
DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
BOARD FLOORPLAN
Figure 1 shows the board layout for the DS2149DK. The DS2149 PLCC socket is in the center of the board. The line-side bantam connectors for the Tx and Rx differential pairs and transformers are at the bottom of the board, while the system connector and configuration jumpers are at the top. The LEDs for INT, INLOOP, and RCL/QPD are in the center of the board, right above the DS2149 socket. The power-supply connectors and power indicator LED are in the upper left corner of the board, while the DB9 serial connector is the upper left. A T1 oscillator sits to the left of the DS2149 socket below a switch for changing the voltage to the DS2149 socket from 5V to 3.3V. Please refer to the general locations on the board when this document references specific items on the DS2149DK.
Figure 1. Board Floorplan
POWER JACKS GND VDD
SYSTEM CONNECTOR
LEDs NLOOP
SERIAL PORT
PWR LED
RCL INT
Dallas Semiconductor DS2149DK/ DS21349DK
OSCILLATOR DS2149 T1
CONFIGURATION JUMPERS
TRANSFORMERS Tx Tx Rx
CONFIGURATION SWITCHES
LINE CONNECTORS Tx Rx
3 of 14
DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
LINE-SIDE CONNECTIONS
The DS2149DK/DS21349DK implements the Tx and Rx line interface networks recommended in the DS2149 and DS21349 data sheets and as shown in Figure 2. To connect the DS2149DK/DS21349DK to T1 or J1 test equipment, connect the equipment to the RJ48 connector or to the two bantam connectors, J2 and J3. Please notice the relays disconnecting TTIP and TRING on T1 and T2. These relays disconnect the series resistors R4 and R5, which is recommended for some long-haul configurations. Pin 16 on the system connector serves as the control line for the relays. When pin 16 is high, T2 is enabled with TTIP and TRING. When it is held low, T1 is enabled with TTIP and TRING.
Figure 2. Line-Side Circuitry
J2 TRANSMIT T1 C2 1mF
TTIP TRING
T2 R4 4.7W (1%) R5 4.7W (1%) T3 R9 50W (1%) Dallas Semiconductor DS2149/DS21349
J3 RECEIVE
RTIP
RRING
R8 50W (1%)
4 of 14
DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
SYSTEM CONNECTOR
A 16-pin system connector at the top of the board gives access to the following signals: RPOS, TPOS, RNEG, TNEG, RCLK_CON, TCLK, MCLK, VDD, GND, CS, SCLK, SDI, and RELAY_CONTROL. By using jumpers to connect TCLK to RCLK_CON, TPOS to RPOS, and TNEG to RNEG, the system connector can also be used to implement an external remote loopback. Additionally, the system connector can read and write to the device without going through the on-board microcontroller. With this feature, you can quickly use this design kit as a working prototype and begin writing firmware for your system. Figure 3 shows a representation of the system connector.
Figure 3. System Connector
RPOS TPOS RNEG TNEG RCLK TCLK MCLK VDD CS SCLK SDI SDO GND GND GND RELAY_CONTROL
POWER-SUPPLY CONNECTORS
Connect a 5.0V power supply across the red (VDD) and black (GND) banana jacks. The red PWR LED indicates power is applied to the board. Select the appropriate voltage that needs to be applied to VDD from the power switch below the PWR LED, depending if you are using a DS2149 (5V) or DS21349 (3.3V).
MICROCONTROLER AND SERIAL CONNECTOR
The DS2149DK/DS21349DK contains an on-board 8051 microcontroller with factory-installed firmware loaded into the microcontroller's EPROM. This firmware translates memory access requests from the RS-232 serial port into register access to the DS2149 or DS21349 in software mode. DemoView, a software application created by Dallas Semiconductor, allows easy read-write access for this device.
INSTALLING AND RUNNING THE SOFTWARE
DemoView is a general-purpose program that supports several Dallas Semiconductor design kits. To install the DemoView software, run SETUP.EXE from the DemoView.ZIP file. (Download DemoView.ZIP from our website, After installation, run the DEMOVIEW.EXE program with the www.maxim-ic.com/telecom.) DS2149DK/DS21349DK board powered up and connected to the PC. In the opening screen, click the REGVIEW button. Select the correct serial port in the Port Selection dialog box, then click OK. To configure DEMOVIEW to support the DS2149DK/DS21349DK, open the File pulldown menu and select Definition File. In the Choose Definition File dialog box, select DS2149DK.DEF and click Open. After selecting the definition file, the main part of the REGVIEW window displays the DS2149's memory map. To select a register, click on it in the register map. When a register is selected, the full name of the register and its bit map are displayed at the bottom of the REGVIEW window. Bits that are logic 0 are displayed in white, while bits that are logic 1 are displayed in green.

The DemoView software supports the following actions: Toggle a bit. Select the register in the register map and then click the bit in the bit map. Write a register. Select the register, click the Write button, and enter the value to be written. Write all registers. Click the Write All button and enter the value to be written. Read a register. Select the register in the register map and click the Read button. Read all registers. Click the Read All button.
5 of 14
DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
BASIC CONFIGURATION
The following example configurations provide a quick start to using the DS2149DK/DS21349DK, although there are many ways they can be configured. To set up other configurations, refer to the DS2149/DS21349 data sheets in addition to this data sheet. T1 Hardware Mode--External Remote Loopback 1) On the system connector, jumper TPOS to RPOS, TNEG to RNEG, RCLK_CON to TCLK, and RELAY_CONTROL to GND. 2) JP8, jumper RCLK to CON. 3) Remove JP5, TCLK_EN. 4) Jumper JP6 MCLK_EN. 5) JP9, JASEL, jumper to GND. 6) JP7, TAIS, jumper to GND. 7) JP10, MODE0, jumper to GND. 8) Jumper JP3, MODE1_EN. 9) Jumper JP4, RLS_EN. 10) Jumper JP2, LLB_EN. 11) On SW1, switch MODE1 to MODE1_LO. 12) On SW1, switch L0 to L0_HI. 13) On SW1, switch L1 to L1_HI. 14) On SW1, switch L2 to L2_LO. 15) On SW1, switch L3 to L3_LO. 16) On SW1, switch RLB to RLB_LO. 17) On SW1, switch LLB to LLB_LO. 18) Place appropriate device in socket. 19) Select the power 5V or 3V depending on which device you use. 20) Connect J2 and J3 to test equipment Device should be in external remote loopback. T1 Software Mode--External Remote Loopback 1) On the system connector, jumper TPOS to RPOS, TNEG to RNEG, RCLK_CON to TCLK, and RELAY_CONTROL to GND. 2) JP8, jumper RCLK to CON. 3) Remove JP5, TCLK_EN. 4) Jumper JP6 MCLK_EN. 5) JP9, JASEL, jumper to GND. 6) JP7, TAIS, jumper to GND. 7) JP10, MODE0, jumper to GND. 8) Jumper JP3, MODE1_EN. 9) Jumper JP4, RLS_EN. 10) Jumper JP2, LLB_EN. 11) On SW1, switch MODE1 to MODE1_HI. 12) Place appropriate device in socket. 13) Select the power 5V or 3V depending on which device you use. 14) Connect J2 and J3 to test equipment. 15) Load the DemoView software. 16) Select RegView. 17) Load the DS2149.DEF file. 18) Write CR1 to 0x03. 19) Write CR2 to 0x00. 20) Write CR3 to 0x00. 21) Write CR4 to 0x00. Device should be in external remote loopback.
6 of 14
DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
DS2149/DS21349 INFORMATION
For more information about the DS2149 and DS21349, please consult the DS2149 and DS21349 data sheets available on our website, www.maxim-ic.com/telecom.
TECHNICAL SUPPORT
For technical support, please email your questions to telecom.support@dalsemi.com.
SCHEMATICS
The DS2149DK/DS21349DK schematics are featured in the following 14 pages.
7 of 14

▲Up To Search▲

Price & Availability of DS2149DK

	To Download DS2149DK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .